Discovering Plumbing Basics is Vital for Bathtub Installation
Discovering Plumbing Basics is Vital for Bathtub Installation
Blog Article
The content down below in relation to Tools You Need to Install a New Bathtub is really enlightening. You should investigate it.
Installing a bathtub isn't specifically rocket science, however it does require strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a brand-new one is also a moderately challenging task. If the old tub is readily easily accessible, the job can move rapidly; if you have to open up a wall to remove the old tub and also position the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and embeded in the new one. See to it you have certified yourself for the job as well as are comfortable trying it. As opposed to working with a service provider to take over a halfway-completed job, it is better to think about utilizing one before you begin. Chances are you might require a specialist plumber to make tube links.
This write-up will certainly aid you set up a brand-new bathtub in your restroom if you have currently purchased a brand-new bathtub as well as do not require to change the arrangement of your previous water system pipelines.
Your tools and material list need to consist of the following:
Getting ready for the Setup
To start with, the supporting framework supplied with the bathroom needs to be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to avoid strain on the tub.
Fit the flexible tap ports to the bottom of both taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its final position.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be fairly troublesome as a result of the restricted accessibility that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Utilizing both wooden boards under its feet, place the tub in the needed position. The wooden boards are useful in uniformly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four little factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as readjusting the feet on the bathtub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the supply of water as well as inspect all joints as well as new pipework for leaks as well as tighten them if needed. Load the tub as well as also inspect the overflow outlet and also the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub must wait till the tub has actually been made use of at least when as this will certainly resolve it into its final setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the faucet and the sink. Secure the faucet in position with the supplier offered backnut. Once the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous type must be attached to the faucet ends initially, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, creating the water to permeate the wall surface in between the bath as well as the tiling, resulting in problems with moisture and also possible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water prior to sealing, to enable the motion experienced when the tub remains in use. The sealer can split rather very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that write-up on A Step-by-Step Guide to Installing a Bathtub from an acquaintance on our other site. Appreciated our post? Please share it. Help others find it. I praise you for your time. Visit us again soon.
We're your answer! Report this page